How To Make Tire Planters
|
| Here is a picture of a couple of the swans I have made from tires. - Jase |
Christopher Lowell's Tire Planter
I have instructions for a tire planter from the Christopher Lowell Show. (Outdoor dynamics for Dummies show).Materials
- Old tire with/without rim
- Sharp kitchen knife
- chalk
- potting soil
- spray paint
Directions
Draw pattern with chalk along side wall on one side of tire. Space scallops/ or ^^^ evenly around tire. Start at tread and end close to rim. Cut out with knife, using straight up and down motion, pointing blade away from yourself. This wil separate the tire into two pieces. Place your foot in center of rim and pull one scalloped edge toward yourself, this turns it inside out. Continue until it forms planter with pedestal. Fill with potting soil. Can spray paint planter to jazz it up.
Good luck, I am going to make mine this week.
By Claudia
Editor's Note: Here is a link to Christopher Lowell's instructions, including photos.Felder Rushing Style Planter
Penn State College of Agricultural Sciences has great insturctions for making a tire planter: "Finding the right tire is essential in making a tire planter. The tire you select should be well worn, and pliable in the shoulder area of the tire (what Felder calls the "sweet spot"), just below the tread. You can tell if the tire is a good candidate by pushing in on the shoulder area with the palm of your hand. If there is plenty of "give" in this area, the tire should be easy to work with. If not, you should find another one to use."
Read the rest here:
Swan Planters
You can make a swan planter out of a tire. At RonsSwan.com they have a PDF with step by step instructions. They recommend using a scooter tire:Type of tyre
The kind of tyre you use is important. An ordinary car tyre has steel belting so is near impossible to cut and will have sharp edges. I made Ron from old Vespa motor scooter tyres as they are easier to cut. If you could source some very old car tyres which are textile belted, they would be suitable, but still very hard to cut by hand.
To downlod the PDF go to http://www.rondswan.com and click on the "AboutRon" page. At the bottom of the page is the how-to.
Feedback About This Post:
RE: How To Make Tire Planters
I would like to find out more ideas for tire crafts?
Post By Martha (Guest Post)
RE: How To Make Tire Planters
I have been rolling around on the ground for 4 hours trying to turn a tire inside out. I have cut 2" back from the bead on both sides. I want to use this as a pedestal for a rain barrel. Looking at some of these, I must be missing something.
Post By sweeper (Guest Post)
RE: How To Make Tire Planters
Super swans. They make hanging baskets shaped/painted like parrots and toucans in Costa Rica. Hope the picture comes out o.k.
Post By pennsybob1 (Guest Post)
RE: How To Make Tire Planters
Someone who is more creative than I came up with the idea I'm using this year. I got tires, painted them terra cotta color and painted inside the zigzagged treads with turquiose, yellow, orange and red. Viola -- they look like Mexican pottery!!!
Post By Marna (Guest Post)
RE: How To Make Tire Planters
i love this thank you so much for posting ill be keeping my eye out for those tires as i have lots and lots of space for them
Post By denise w (Guest Post)
RE: How To Make Tire Planters
How cute! How did you ever come up with an idea like this?
Post By ALISON (Guest Post)
Disclaimer: ThriftyFun.com cannot accept any responsibility for any injury or damage that you may cause to yourself, others, or property when following any advice given on this site. Read the full disclaimer: http://www.thriftyfun.comdisclaimer.ldml If you find any information on ThriftyFun.com or in our newsletters that is either erroneous and/or potentially harmful to others, please Contact Us, immediately.