social

Cleaning Outside of Revere Ware Pots?

My Revere Ware has sufficient build up of burnt food on the OUTSIDE (sides and bottom) of the pots and pans. There is advice on cleaning the INSIDE not the OUTSIDE - I'm considering using a Magic Eraser but I'm wondering about the copper bottom as well. Would be interested in detailed information. Thanks so much!

Advertisement



Kris from Austin, TX

Add your voice! Click below to answer. ThriftyFun is powered by your wisdom!

 

Silver Feedback Medal for All Time! 290 Feedbacks
December 4, 20070 found this helpful

www.thriftyfun.com/tf81763537.tip.html

Read last post on page.

 
By jean (Guest Post)
December 4, 20070 found this helpful

Try soaking the pots in a sink or dish pan in hot water and powder dish washer detergent, about 1 cup to a sink full. What works on the inside will probably work on the outside. Soak overnight, then scrub.

 

Bronze Request Medal for All Time! 65 Requests
December 6, 20070 found this helpful

I'm not sure if this will help you, but my mother taught me how to clean and brighten copper bottoms of our Revere Ware pots and pans.

Wet the copper bottom and sprinkle vinegar (any kind) on it. Then sprinkle regular salt on top of the vinegar and scrub with a sponge. The chemical reaction of the vinegar and salt removes tarnish from the bottom.

Advertisement

Maybe this will help, I hope.

Good luck!
Smoochie :)

 
November 21, 20170 found this helpful

Didnt work that well. It did shine the bottom of the pan that wasnt totally ingrained. Mine has a medium brown color ingrained all around the copper finish. I have a 7 in. Revere Ware frying pan that makes the best scrambled eggs.

 
December 5, 20170 found this helpful

Wow--vinegar and salt just did a great job! Thanks!

 
December 6, 20070 found this helpful

Barkeeper's Friend!

 
February 21, 20191 found this helpful

The original BKF is too abrasive for the copper; I do not recommend it. They make several products; check their web site and/or contact the company for what you can use that won't hurt the vintage copper.

 
February 9, 20080 found this helpful

I've had to do a lot of this lately.
First, do a thorough cleaning with Bar Keepers Friend-- on the stainless steel and the copper. Don't spend a lot of time on the copper because that's Step 2.

Advertisement


Step 2: Get on down to the local hardware store and pick up a sheet of 600 grit wet/dry sandpaper. Cut off a piece around 2" square and keep everything wet. Then scour the copper with the sandpaper. That copper will shine like you won't believe...
(Maybe going to the hardware store should have been step number 1?)

 
February 9, 20081 found this helpful

Before anyone says: "Yikes! Sandpaper? Are you kidding me?"
I heard this tip on a cooking show on a San Francisco radio station. And it really works well, without scratching the copper. I was amazed myself!

 
March 3, 20082 found this helpful

I have the solution to your problem, this will work on the copper bottom & the inside that was burned from water, milk etcetera. My husband is a body work man fixing & painting cars. When he paints cars afterwards, he has to wet sand & buff the paint to get out imperfections. He uses a 1000 grit or 1,500 grit sandpaper, it's really fine grain. I use it on the inside & the outside of my Revereware pans. You have to let a slow flow of water run on it the whole time you are scrubbing. It does not scratch the pans because it's such a fine grain of sandpaper. I promise you, it will not scratch & they come out looking brand new.

Advertisement

You have to remember to run a trickle of water over it as your scrubbing. You are wet sanding the burnt stuff & film off the pan. If it works on car paint without scratching, it will work on your pans. I have been using this method for 20 years now with perfect looking pans. You can get the sandpaper at the hardware or automotive store, ask for 1000 grit to 1,500 wet dry sandpaper. It doesn't take much scrubbing either.

I promise you will never go back to any other way again after using this method.

 
March 3, 20080 found this helpful

I just posted about the sandpaper too,when people think of sandpaper they think of the rough stuff.There is a sandpaper out there that is 1000 grit and 1,500 grit,you have to get the right type.It's called wet/dry 1000 grit sandpaper,it's the type used to wet sand and buff out imperfection in the paint after a car is painted.I use this method and I promise you it does not scratch your pans.You have to REMEMBER to run a trickle flow of water over the pan as your wet sanding it.It's more like a rubbing method but it WILL NOT SCRATCH YOUR PANS.If it does than you have used the wrong grit,it has to be 1000 grit or 1,500 wet/dry sandpaper,it is a very very fine sandpaper grit.Once you use this method you will never bother with others again,it works on the inside and the outside of the pan.

 
February 21, 20190 found this helpful

What about enameled - painted - pans? I have a vintage Dansk enameled pan that, after BKF, is no longer smooth and shiny - a cloth "drags" over the finish, which looks kind of splotchy and somewhat pitted. Lightly wet sand with 1500? (PS - we're very familiar with it, as we've done amateur body work on our everyday vehicles, and also have some antique show cars; we leave major paint work to the pros, but have done some small fixes.) I'm thinking either that or a very mildly abrasive rubbing compound we got from McGuires for removing water spots.)

 
By CatnMouse (Guest Post)
July 29, 20080 found this helpful

I just picked up a set of Revere Ware copper bottom pots at a yard sale...for $1.00! I cleaned them all up bright and shiny with the same stuff I use on my brass bathroom sink, Cameo copper, brass and porcelain cleaner which costs about $1.25 at my local grocery store.

 
May 31, 20220 found this helpful

I haven't tried it yet but I was thinking of using Bon Ami to clean the stainless steel outside of my ancient family heirloom Revere Ware teakettle before using a high-temperature high-strength epoxy to reattach the small barrel nut formerly attached to the teakettle (since the 1960s!) which holds the handle in place from the bottom with a small Phillips head screw inserted through the top.

Advertisement

I actually took my teakettle to a guy who does welding and he said that he wouldn't try spot welding as I'd advised by someone else because it could cause the teakettle to explode. Don't want that!

I also have a car door handle on my rear passenger side door that broke yesterday. I can still open the door by reaching through the front door and using the interior handle of the rear door, but I'm going to try the same J-B Weld product on that because why not? It's a nice clean break in which a big chunk of the plastic handle snapped off after "only" 16 years of UV exposure, mostly in the Deep South. If it holds together so as to actually function in the future, great. And if it doesn't, oh well.

In case anyone's interested, the product is J-B Weld Original Cold-Weld Steel Reinforced Epoxy, which set me back $8.99 + tax at our local Ace Hardware. They say on the packaging that its tensile strength is 5,020 PSI, and that it can withstand temperatures up to 550° F. when fully cured.

Advertisement

I've obviously gotten a bit off topic but maybe my discussion will help someone else. I simply want to get the surface of my teakettle good and clean so the epoxy will actually work to secure the barrel nut. If Bon Ami doesn't work I'll try the fine gauge sandpaper recommended here. I think I may even have some on hand!

 

Add your voice! Click below to answer. ThriftyFun is powered by your wisdom!

 
In This Page
Categories
Home and Garden Cleaning DishesDecember 4, 2007
Pages
More
🐰
Easter Ideas!
🌻
Gardening
🍀
St. Patrick's Ideas!
Facebook
Pinterest
YouTube
Instagram
Categories
Better LivingBudget & FinanceBusiness and LegalComputersConsumer AdviceCoronavirusCraftsEducationEntertainmentFood and RecipesHealth & BeautyHolidays and PartiesHome and GardenMake Your OwnOrganizingParentingPetsPhotosTravel and RecreationWeddings
Published by ThriftyFun.
Desktop Page | View Mobile
Disclaimer | Privacy Policy | Contact Us
Generated 2024-03-16 05:16:49 in 3 secs. ⛅️️
© 1997-2024 by Cumuli, Inc. All Rights Reserved.
https://www.thriftyfun.com/tf18277176.tip.html