social

Trouble With A Sewing Machine?

I was trying to fix a sluggish and squeaky sewing machine. I somehow managed to make it worse. The problem is the big wheel on the right hand side doesn't catch and therefore will spin and not move the "works" up and down like it is supposed to. The belt is on and I have cleaned and oiled every moving part I can find. Any ideas? It is a Simplicity Classic.

Advertisement



painterjayne from Minnesota

Add your voice! Click below to answer. ThriftyFun is powered by your wisdom!

 
May 5, 20080 found this helpful

I know my sewing machine has a smaller wheel on the large one that is used to loosen and "disconnect" the needle drive while winding bobbins. It sounds like this might still be loose on yours? This may be an overly simple answer; but certainly worth a check.

It should be turned away from you to tighten it (clockwise).

 
May 5, 20080 found this helpful

Thanks for the feedback. I have tightened and loosened that smaller wheel and I still can't get the big wheel to engage the moving parts. When I rotate the smaller wheel counter clockwise it seems to have the force needed to make the parts move BUT when I turn the bigger wheel counter clockwise it won't engage.

Advertisement

Also, when I turn the power on, same thing...with the little wheel tightened as it should be, the "big wheel keep on turnin" counter clockwise and doesn't engage.

 
May 5, 20080 found this helpful

Gosh, doesn't sound simple, then! I would take it to the sewing maching repair place, if it were mine, because I wouldn't want to mess it up while trying to fix it. Check your yellow pages; usually shops can give you an estimate before they do the work. I have been very happy with ours.

 

Bronze Post Medal for All Time! 213 Posts
May 5, 20080 found this helpful

You accidentally kicked the machine out of gear. It's supposed to "pop out" for when you wind the bobbins (that way your machine won't go up & down as you wind your bobbins). Depending on your machine (each one works differently). First, see if you have a "button" in the center of the machines "big wheel on the right side". If so, then push it in & that should fix your problem!

Advertisement

But, on some machines, the bobbin winder moves to the left or the right & these kinds of machines don't have a button in the center of the wheel. If this is your machine then move the bobbin winder to the left or right. You will hear it click back in to gear. I'm pretty sure one of these things will fix your problem. If not & you have a belt-driven machine then your belt may be old & loose which causes slipping & you may need a newer, tighter belt (They cost under $10 at sewing & vacuum repair stores).

Write me here on ThriftyFun. I have a machine from just about every decade since 1913 & have owned lots of older machines from the 1960's, 70's, 80's, 90's etc, etc. (I buy them at thrift stores) But, if it's a new "computer" machine, then I might not know how to help you, but if it's a classic machine then odds are I can help. First try what I suggested above, then drop me a note here on ThriftyFun & let me know what happened. Cyinda

 

Add your voice! Click below to answer. ThriftyFun is powered by your wisdom!

 
Categories
Home and Garden Repair Machines Sewing MachinesMay 5, 2008
Pages
More
💘
Valentine's Ideas!
🎂
Birthday Ideas!
🍀
St. Patrick's Ideas!
Facebook
Pinterest
YouTube
Instagram
Categories
Better LivingBudget & FinanceBusiness and LegalComputersConsumer AdviceCoronavirusCraftsEducationEntertainmentFood and RecipesHealth & BeautyHolidays and PartiesHome and GardenMake Your OwnOrganizingParentingPetsPhotosTravel and RecreationWeddings
Published by ThriftyFun.
Desktop Page | View Mobile
Disclaimer | Privacy Policy | Contact Us
Generated 2024-01-27 12:25:24 in 3 secs. ⛅️️
© 1997-2024 by Cumuli, Inc. All Rights Reserved.
https://www.thriftyfun.com/tf36980559.tip.html