social

Caulk Not Sticking to Fiberglass Shower?

We have recently had a new fiberglass shower surround installed and we are having a hard time getting the caulk to stick. When it is applied it looks great, but after a shower or two it starts to ripple and comes off. Any suggestions for preparing the fiberglass before reapplying the caulk?

Advertisement



Kathy from Champlin, MN

Add your voice! Click below to answer. ThriftyFun is powered by your wisdom!

 
January 8, 20090 found this helpful

You can wipe the surface area down with Denatured Alcohol, or for a more industrial cleansing, try Acetone...(if you can find it....Acetone is now in the 'cancerous' listings, along with sex and breathing air )
Both are available in the Hardware Dept...
Read the applications on the tubing; and check with Ace Hardware for a better selection of types..

 
By Harry (Guest Post)
January 8, 20090 found this helpful

My first question is what type of caulking are you using; not the brand. The area to be caulked should be clean and dry.

Advertisement

I would apply a silicone sealer. Other types of sealer may not be compatibly with the water.

 
By HSLINKS (Guest Post)
January 14, 20090 found this helpful

Any chance the seam was wet inside from the night before?

Any mold issues? If there is mold it will not stick

Fill the bathtub before putting in/on caulk. This will separate the tub & surround a little (you may not even see the difference). Water is about 8# per gallon so it adds up quickly

Wipe down with alcohol and make sure its dry. Take some tape and run it about 1/4 inch above and below where the caulk goes (leave enough area for the caulk - don't measure from the center line)

Buy silicon caulk - it comes in colours and clear.

Cut tip at a slight angle and don't cut too far down you want a small hole. Use bamboo skewer, hanger wire, long long nail etc to poke hole the seal

Advertisement

Have a small container of water, a rag. Run your bead of caulk all around the tub. Come back with finger dipped in water to smooth out the caulk - wipe off excess

Let dry. I carefully take a razor and barely scratch at the tape/caulk seam. Pull tape slowly.

Let it dry more. Read the label how long does it say before you can get it wet? I do a bath the first time not a shower just so I make SURE its done. Ria

 
March 3, 20090 found this helpful

White vinegar will remove any soap scum that may be preventing the caulk from sticking.

 
February 23, 20220 found this helpful

Bathroom cleaner like scrubbing bubbles clean real well but can make everything not stick. Caulk paint etc. Try cleaning the are with the alcohol or acetone really well.

Advertisement

I am by no means an expert just what I experienced

 

Add your voice! Click below to answer. ThriftyFun is powered by your wisdom!

 
Categories
Home and Garden Repair Home BathroomJanuary 8, 2009
Pages
More
🎂
Birthday Ideas!
💘
Valentine's Ideas!
🍀
St. Patrick's Ideas!
Facebook
Pinterest
YouTube
Instagram
Categories
Better LivingBudget & FinanceBusiness and LegalComputersConsumer AdviceCoronavirusCraftsEducationEntertainmentFood and RecipesHealth & BeautyHolidays and PartiesHome and GardenMake Your OwnOrganizingParentingPetsPhotosTravel and RecreationWeddings
Published by ThriftyFun.
Desktop Page | View Mobile
Disclaimer | Privacy Policy | Contact Us
Generated 2024-02-03 08:39:19 in 2 secs. ⛅️️
© 1997-2024 by Cumuli, Inc. All Rights Reserved.
https://www.thriftyfun.com/tf69320294.tip.html