social

Recycled Light Bulb Wall Vase

July 4, 2011

Clean out the inside of an old light bulb to create a clever wall vase. Yes, light bulbs are very fragile, but with care and patience they can be repurposed into an unusual art piece. Once opened and cleaned out, your new vase can hold water for fresh flowers, buttons, beads, or other small filler trinkets. Light Bulb Wall Vase - finished bulb filled with beads

 

Note:

Advertisement


The metal screw end of the light bulb is the top when referred to in the instructions. Warning: Wear safety goggles and gloves when attempting this project.

Approximate Time: 1 hour

Supplies:

Instructions:

  1. Cover your work surface with an old bath towel. Use the side of a sharp knife to pry up the edge of the disk covering the top of the light bulb. Grasp the edge with needle-nose pliers and peel the disk off the top. Light Bulb Wall Vase - light bulb lying on towel
     

    Advertisement

  2. There is a solid ceramic plug in the top of the bulb. That is the black top shown in the pictures. Hold the metal screw end with one hand and firmly jab the plug with the tip of the needle-nose pliers. When the plug cracks, use the pliers to grab the edges and pull out the pieces. Note: When jabbing the end with the pliers, hold the bulb above your work space, not on it. This will prevent the bulb from taking any of the impact. Do not squeeze the bulb too tightly. Light Bulb Wall Vase - shattered pieces of ceramic plug after removal
     

  3. There is a thin glass tube just inside the opened end. Grab the tube with the pliers and twist it off and out. There will be a small puff of air, so do this step with the opening of the bulb facing down toward your towel. Light Bulb Wall Vase - glass tube removed from bulb, lying on towel work surface
     

    Advertisement

  4. The next level is a finger-like glass tube. The wires and glass "insulators" are in this tube. Hold the metal end and suspend the bulb above your work surface. Poke the end of a screwdriver into the bulb and pound the seal at the top of the tube. Once broken, insert your closed needle-nose pliers into the bulb and twist around the opening to break away the remaining glass of the tube. Shake out the broken glass and wires. If the wires get stuck in the opening, grab them with the pliers and pull them out. Light Bulb Wall Vase - bits of ceramic plug, glass tube, wires, and insulators on towel
     

  5. Cut a 20-inch length of craft wire using wire cutters. Wrap the wire around the bottom edge of the metal screw end. Bring the ends together and twist to secure it to the bulb. Light Bulb Wall Vase - craft wire wrapped around the screw end of bulb
     

    Advertisement

  6. Cut a scrap of weathered wood approximately 7 inches wide by 10 inches long using a jigsaw. The exact dimensions are not important. If you find a piece that is close in size, it can be used without the need for cutting. Light Bulb Wall Vase - weathered wood scrap
     

  7. Lay the wood on your work surface. The side facing up will be the front. Lay the bulb on its side and center it on the board. Use a marking pen to make a dot on each side of the screw end where the wire is attached. Light Bulb Wall Vase - marking placement of the bulb
     
    Remove the bulb. Drill holes through the board at each dot using a 1/16-inch drill bit.

    Advertisement

  8. Lay the bulb back on the board. Insert one end of the twisted wire through one hole and the other end through the remaining hole. Bring the wire ends together on the back of the board and twist to secure. Light Bulb Wall Vase - wire pulled to back side of board
     

  9. Place your index finger over the twist and between the two wire ends. Bring the wire ends together above the finger and twist. Remove your finger. The loop created by your finger is the hanger for the board. Clip off the excess wire.

  10. Fill the bulb with your desired trinkets or water, add a flower and decorate with a bit of lace around the neck.

    By cyndee kromminga from Winfield, KS

    Comments

    July 6, 20110 found this helpful

    This is very pretty! It would be a great and attractive way to root cuttings like Coleus, etc. I would have to use my oven bulbs as we use CFL''s everywhere else. Thanks so much!

     
In These Pages
Categories
Crafts Recycled Crafts DecorApril 5, 2017
Pages
More
💘
Valentine's Ideas!
🎂
Birthday Ideas!
🍀
St. Patrick's Ideas!
Facebook
Pinterest
YouTube
Instagram
Categories
Better LivingBudget & FinanceBusiness and LegalComputersConsumer AdviceCoronavirusCraftsEducationEntertainmentFood and RecipesHealth & BeautyHolidays and PartiesHome and GardenMake Your OwnOrganizingParentingPetsPhotosTravel and RecreationWeddings
Published by ThriftyFun.
Desktop Page | View Mobile
Disclaimer | Privacy Policy | Contact Us
Generated 2024-02-08 16:52:18 in 5 secs. ⛅️️
© 1997-2024 by Cumuli, Inc. All Rights Reserved.
https://www.thriftyfun.com/tf99451049.tip.html