Repairing a Torn Vacuum Cleaner Hose

RE: Repairing a Torn Vacuum Cleaner Hose By ARlene (Guest Post) What type of vacuum cleaner bag does this use? I just inherited this vacuum cleaner it works great and I used duct tape to fix the hose. Posted on 09/16/2007 | Report Spam or Abuse RE: Repairing a Torn Vacuum Cleaner Hose By Keith a.k.a Mcgiver (Guest Post) Ok I agree duct tape would work fine, if this was my project i would try Ace Hardware or Home Depot for shrink tubing (just slightly larger than the hose) this would allow it to slide over. Detach ur hose slide a 4 inch piece of s-tubing centered over the split then use the heat from a hair dryer to shrink the tubing. This will be flexible and long lasting, good luck my fellow makeshifter Posted on 07/29/2007 | Report Spam or Abuse RE: Repairing a Torn Vacuum Cleaner Hose By Pat (Guest Post) I, too used duct tape successfully Posted on 06/30/2007 | Report Spam or Abuse RE: Repairing a Torn Vacuum Cleaner Hose By Maryeileen (698) Profile Contact Use black electrical tape- it will take the "heat". I think duct tape's glue would get sticky. Posted on 06/28/2007 | Report Spam or Abuse RE: Repairing a Torn Vacuum Cleaner Hose By Jantoo (734) Contact Duct tape. I had a Kenmore canister vacuum for many years, and by the time I gave up on it, it still worked but the motor heated up too quickly. And the hose was almost entirely covered with duct tape. It's a good machine. Posted on 06/27/2007 | Report Spam or Abuse RE: Repairing a Torn Vacuum Cleaner Hose By kimmcg (176) Contact Well this is finally a case where I can say "Been there, done that!" I accidentally vacuumed up a small pencil form under my sons bed and it tore a small hole in my vacuum hose too! I took out one of his bicycle tire repair kits (from walmart) and fixed it as you would a bike tire! Its been about 2 yrs now and its still holding up perfectly. Hope you give it a try.. i know it will work :) Kim Posted on 06/27/2007 | Report Spam or Abuse RE: Repairing a Torn Vacuum Cleaner Hose By Lynn (750) Contact Duct tape. Hot glue will come off as it flexes. Posted on 06/27/2007 | Report Spam or Abuse RE: Repairing a Torn Vacuum Cleaner Hose By denise (Guest Post) my very first thought was to use a hot glue gun. Posted on 06/27/2007 | Report Spam or Abuse RE: Repairing a Torn Vacuum Cleaner Hose By kimhis (1411) Contact You can tear the duct tape into narrower strips so that it will adapt better to the corrugated contours. You could use a hose clamp from the auto parts department if it needs reinforcement to stop the bending from worsening the hole. Thanks for the pic! Posted on 06/27/2007 | Report Spam or Abuse RE: Repairing a Torn Vacuum Cleaner Hose By pam2cats (68) Profile Contact I can't believe that duct tape isn't the first thing that comes to your mind to fix anything! LOL It even comes in lots of different colors now. Posted on 06/27/2007 | Report Spam or Abuse RE: Repairing a Torn Vacuum Cleaner Hose By Noella (249) Profile Contact Back in my single days and before I could afford a new hose, I used duct tape. Works great. The split will still get bigger and the duct tape will attract dust and dirt. But the nice thing about it is that you can rip off the old nasty duct tape and put on new. Duct tape also comes in a variety of colors at your local Wal-Mart, so you might be able to match the color of the hose. Posted on 06/27/2007 | Report Spam or Abuse RE: Repairing a Torn Vacuum Cleaner Hose By Deb (Guest Post) Duct Tape!! I have it on my basement vacumn for years and it's still holding. Posted on 06/27/2007 | Report Spam or Abuse RE: Repairing a Torn Vacuum Cleaner Hose By mommy8532 (9) Profile Contact As my husband used for ours till the motor goes or the whole hose goes- use duct tape. I know it looks tacky but it does get the job done. I have had it one there for about 6 months and it still runs great. have a good one. Posted on 06/26/2007 | Report Spam or Abuse RE: Repairing a Torn Vacuum Cleaner Hose By ThriftyFun (3117) Profile Blog! Contact I'd get some bathroom caulking, shoe goo, or some kind of rubber caulk. Clean the surface very well and have it very dry, then apply to the cracked place. Let it dry thoroughly before using. It will be flexible so would probably work. If all else fails, duct tape can be used but it does look a lot more tacky. Make sure the surface is good and clean before sticking it down and form around the bumps (wires) in the hose. Susan from ThriftyFun Posted on 06/26/2007 | Report Spam or Abuse

Post Feedback: Login using the form on the top of the page to post feedback (if you are a registered user). If you have not yet registered, click here to do so. It's FREE!.