social

Making Soda Can Plant Labels


Gold Post Medal for All Time! 858 Posts
September 17, 2009

finished plant labelOne of my favorite garden crafts is making homemade plant labels from aluminum cans and wire clothes hangers. Not only are they inexpensive and durable, but these labels are actually attractive and fun to make. They are designed to dangle freely on their supports, so when the wind blows their movement makes a gentle clinking noise, turning your tiny reflective plant labels into a collective army of rabbit repellents.

Advertisement

Materials:

supplies
 

Directions:

  1. Put on your gloves.
  2. Use the tip of your scissors to punch a small hole on the side of each end of the can. If your scissors isn't sharp enough, use a steak knife or screwdriver to get the hole started.
  3. Using your scissors, cut off the top and bottom of the can and discard the ends in your recycling bin. If you need to, trim off any excess sharp edges from the remaining piece of aluminum and finesse it a bit until it lays pretty flat.
  4. cutting the soda cans
     

    Advertisement

  5. Cut individual labels from the remaining piece of aluminum according to the desired size. The shape and style of your labels is highly personal. Cut them into circles, triangles, rectangles, even flowers. To add some decorative flair, use fancy corner punches or try trimming the edges with scrapbooking scissors.
  6. I add color-coded brads to my labels (I found some in the shape of flowers). This helps me organize my plantings and remember what color flower is coming up where. You're only limited by your imagination so have fun with it! Just don't forget to leave room to punch a hole for hanging and space to write down the name of the plant.
  7. cosmos label
     

    Advertisement

  8. To write names of plants on your labels, lay them on top of a notebook or thick stack of newspaper and press down hard with a ball point pen. Make sure to press hard enough so that when the ink wears off, the name stays imprinted in the metal. Create a hole for hanging using a paper punch (or a hammer and nail).
  9. Finally, use a wire cutter or tin snips to cut 7-8 inch long support pieces from wire coat hangers. Make an "S" hook at one end using a needle-nose pliers, hang the label on the hook, and pinch the "S" shut to keep it from falling off. Voila! You've got durable, inexpensive plant labels!
  10. working with the wire coat hangers
     

    Comments

    September 17, 20090 found this helpful

    What a great idea. Thanks for sharing, I'm going to attempt to make these.

     
    September 18, 20090 found this helpful

    This is one of the best ideas I've seen in a long time. We too have rabbit and squirrel problems. I hope this helps. Cute, cute, cute.

     
    September 19, 20090 found this helpful

    What a great idea! It'll never rust, the name will stay pressed into the label, and I love your colored brads, to remind you of the color of the flower. Thanks for sharing your creative craft! Deb H.

     
    Anonymous
    May 2, 20160 found this helpful

    Thanks. Terrific idea

     
In These Pages
Categories
Crafts Garden & Yard Plant MarkersMay 22, 2014
Pages
More
🐰
Easter Ideas!
🌻
Gardening
🍀
St. Patrick's Ideas!
Facebook
Pinterest
YouTube
Instagram
Categories
Better LivingBudget & FinanceBusiness and LegalComputersConsumer AdviceCoronavirusCraftsEducationEntertainmentFood and RecipesHealth & BeautyHolidays and PartiesHome and GardenMake Your OwnOrganizingParentingPetsPhotosTravel and RecreationWeddings
Published by ThriftyFun.
Desktop Page | View Mobile
Disclaimer | Privacy Policy | Contact Us
Generated 2024-02-21 23:19:46 in 10 secs. ⛅️️
© 1997-2024 by Cumuli, Inc. All Rights Reserved.
https://www.thriftyfun.com/tf39410479.tip.html