social

Wire Woven Ring


Silver Answer Medal for All Time! 440 Answers

The completed copper ring.I used a copper wire from an old transformer and nails to create a weather tool. So it is not at all expensive and not difficult to make this original ring.

Advertisement

Total Time: 45 Minutes

The completed copper ring.
 

Supplies:

Steps:

  1. Draw a circle on the board equal to the inner diameter of the ring + 0.15 inches.
  2. A circle drawn in pencil
     
  3. Use a protractor to divide the circle into 15-degree sectors.
  4. A circle with rays drawn from the center.
     
  5. Using an awl, mark the points of intersection of the sides of the sectors with the circle. Drive the nails into these points so that the nail heads are not flush. The nails will serve as uprights for weaving.
  6. Adding nails to the circle at each ray.
     
    Advertisement

  7. Bend the wire in half and go around the nail in the front, then behind the next nail, then in front of the next nail, and so on, until you go around all the nails in the circle. As you weave and twist, make sure to pull the wires and keep them nice and tight. Use the awl to straighten the wire.
  8. Winding copper wire around the nails in a pattern.
     
    Winding copper wire around the nails in a pattern.
     
  9. Twist the wires and weave in reverse using the other half of the wire. The wires will be twisted. Weave until you get the desired ring width. I made 7 rounds.
  10. Winding copper wire around the nails in a pattern.
     
  11. Remove the nails from the wood plank and release the woven horizontal part of the ring.
    To fix the woven part, insert the nails back into the holes formed by the wire.
  12. Removing half the nails to expose the woven copper.
     
    Advertisement

  13. Pull out one nail and thread one end of the wire through these holes. Then skip one nail and pull out the next, thread the same end of the wire through the holes. Continue to weave in a round in the same way.
  14. Finishing the copper ring.
     
    Finishing the copper ring.
     
  15. Make another round, but thread the other end of the wire into the holes after removing the nails.
  16. Finishing the copper ring.
     
  17. Cut off the ends of the wire, bend and hide them.
  18. The completed copper ring.
     

Add your voice! Click below to comment. ThriftyFun is powered by your wisdom!


Bronze Feedback Medal for All Time! 170 Feedbacks
June 13, 20210 found this helpful

This is gorgeous, and thank you for posting. I don't have access to transformer wire ... would you have any idea of the gauge (thickness)?

Reply Was this helpful? Yes

Silver Answer Medal for All Time! 440 Answers
June 15, 20210 found this helpful

Thank you. I used wire 0.8 mm thickness (I did not notice that it is written 0.8 inches, of course the thickness is 0.8 mm).

Reply Was this helpful? Yes

Silver Post Medal for All Time! 267 Posts
June 16, 20210 found this helpful

I fixed it in the original, not sure what happened there. :)

Reply Was this helpful? Yes

Silver Answer Medal for All Time! 440 Answers
June 17, 20210 found this helpful

Thank you! :)

Reply Was this helpful? Yes
Advertisement

Add your voice! Click below to comment. ThriftyFun is powered by your wisdom!

In This Page
Categories
Crafts JewelryMay 21, 2021
Pages
More
👔
Father's Day Ideas!
🌻
Gardening
🐛
Pest Control
Facebook
Pinterest
YouTube
Instagram
Contests!
Newsletters
Ask a Question
Share a Post
Categories
Better LivingBudget & FinanceBusiness and LegalComputersConsumer AdviceCoronavirusCraftsEducationEntertainmentFood and RecipesHealth & BeautyHolidays and PartiesHome and GardenMake Your OwnOrganizingParentingPetsPhotosTravel and RecreationWeddings
Published by ThriftyFun.
Desktop Page | View Mobile
Disclaimer | Privacy Policy | Contact Us
Generated 2022-05-10 09:54:33 in 1 secs. ⛅️️
© 1997-2022 by Cumuli, Inc. All Rights Reserved.
https://www.thriftyfun.com/Wire-Woven-Ring.html